Installing an App you bought on JustFly is easy. Just unpack the content of the zipfile you received onto your transmitters SD-Card. If you received a (personal) license, it has been sent in a separate email. Just unpack that one as well.

You should merge with existing folders, if asked. No files will be overwritten when installing for the first time.

After doing so, your SD-Card should look like this, apart from any other existing directories on your SDcard:

If you intend to use the predefined models, copy the "SOUNDS - JUSTFLY" over your "SOUNDS" directory, and be sure to select NO when asked to overwrite. It may be that some of the sound files already exist in a version you instelled previously, and you might not want to overwrite those.

Browsing the SDcard on the transmitter should give the same content. Just scroll to the AppMan.lua:

And execute it by long press ENTER:

And the AppMan will launch:

Installation done, ready for use.

have fun and

Just Fly!

Simply run the AppMan as a one time script, as described in the page Installing Apps.

Select the "Install Models" menuitem, and a confirmation box is shown:

Click enter to intall, or exit to cancel. When the installation is fiinshed, a message is shown:

Now you can exit the script by long press '"EXIT", and enter the model selection screen:

A JustFly category has been added, containing all predefined models to select for copying.

BE AWARE that you should always make a copy before editing the models in the JustFly category. Otherwise, you will loose the original.

Have fun and

Just Fly!

Start at the Home screen. Pressing "EXIT" several times should always bring you there. On OpenTX 2.1, you need a long press "EXIT" to return from the telemetry pages.

Go to the Model Selection Screen (push "MENU" once)

go to an empty slot

long press "ENTER"

and select "restore model".

A popup will apear with all avaiable models

Then select a model starting with "Z20" if you are on OpenTX 2.0.

In al other cases, select the model starting with your radio type code, "X09" for the Taranis (X09D, X09D+ or X09E), "X07" if you are using an X7 or X7S (X07 or X07S). For 'Horus' type radios, check Installing a predefined model on a 'Horus' type radio

Make sure you activate the AppMan model by scrolling down

long press ENTER again

and choose SELECT and press "ENTER"

The star before AppMan indicates it is the active model. Since the AppMan model was preconfigured for using the AppMan, you can now also check if the AppMan is properly installed.

Long Press EXIT until you are at the home screen again.

Now long press "PAGE" to start the AppMan.

 

In this example, there are no other Apps than the AppMan itself installed. Any newly installed Apps will show up automatically.

Have fun and

Just Fly!

If you have already installed the App Manager for your model, nothing needs to be done. The newly installed App will show up in your App Manager after starting your transmitter. You can start the App Manager from the home page by long press PAGE.

All JustFly predefined models have the AppMan pre-installed.

If you want to use the App on your own (existing) models, you need to go to the telemetry setup screen. starting from home page:

Go to the Setup menu by pressing "MENU" once

long press "PAGE" (or press "PAGE" 12 times)

srcroll up a little by pressing the "PLUS" button (or dwn to go through the entire page) until you find the telemetry screen setup

press "ENTER" to edit the None to SCRIPT

press "Enter" and go to the ---, press "ENTER" again

Make sure you select the AppMan out of this list and press "ENTER" again

That's it. You have installed the AppMan on your model.

Just press "EXIT" until you are on the home screen again

Now a long press "PAGE" will get you to your App Manager:

Pay attention: if you use more than 1 telemetry screen, the PAGE button will allow you to change screens after accessing the telemetry screens with long press "PAGE".

Have fun and

Just Fly!

If you have already installed the App Manager for your model, nothing needs to be done. The newly installed App will show up in your App Manager after starting your transmitter. You can start the App Manager from the home page by long press PAGE.

All JustFly predefined models have the AppMan pre-installed.

If you want to use the App on your own (existing) models, you need to copy the "/SCRIPTS/AppMan" folder and rename it to "SCRIPTS/'yourmodel'. This can only be done with the PC, either by removing the SDCard or using the USB connection to access the SDCard.

Go to the scripts directory

Select AppMan with the right mouse button to copy. Press right mouse button again to paste a copy.

Rename the "AppMan - copy" folder to "YourModelName", wathever that may be.

That's all.

If you want to create a new model in the field, and have the App manager and all your apps available immediatly, and you don't want to or you can't connect to a PC, you simply name your new model "AppMan". Back home, you connect to the PC, copy the "SCRIPTS/AppMan" folder to "SCRIPTS/yourNewModel" and you change the name of your model to 'yourNewModel' as well, and you are all set to go.

Pay attention: the PAGE button will allow you to change screens after accessing the telemetry screens with long press "PAGE".

Have fun and

Just Fly!